• Medi-Alarm ProgrAMMing MAnuAl. Ness reserves the right to make changes to features and specifications at any time without prior notification in the interest of ongoing product development and improvement.
• TABLE OF CONTENTS Introduction Packaging Installation Wiring. Inputs Outputs. Program Summary Program Mode Program Options. Peripheral Devices Radio PIR Radio Reed Switch Dialler Alarm reporting Specifications. 100-106 PROGRAM MANUAL.DOC. • ‘HELP’ is required. The Ness Medi Alarm is easy to install and very simple to use.
It is designed to comply with the Australian Standard AS2999 for such devices. Installation The Ness Medi is extremely easy to install and requires no tools. The normal location for the Medi Alarm is at the first telephone installed in the premises. This ensures that the Medi Alarm has priority if it needs to send a message to the central monitoring station. The local telephone sits on top of the Medi Alarm unit to make it as unobtrusive as possible. FRONT PANEL INDICATORS Colour code (AS2999) help YELLOW fault MAINS GREEN cancel WHITE reassurance CANCEL HELP BATTERY FAULT RED HELP LIGHT & BUTTON.
GREEN CANCEL LIGHT & BUTTON. Yellow 7 segment display used for PROGRAM mode and FAULT indication.
Green MAINS FAIL steady = normal, flashing = mains fail Yellow LOW BATTERY off = normal, flashing = low battery FAULT off = normal, flashing = fault. PROGRAM SUMMARY Display Option Default Transmitter 1 Program Transmitter 2 Program Transmitter 3 Program Transmitter 4 Program Transmitter 5 Program Transmitter 6 Program Transmitter 7 Program Transmitter 8 Program System Check Dial Type (Aus / NZ) Primary Phone Number Secondary Phone Number Client Account Number Over Due Timer Enable. • 0.5 seconds, followed by ‘1’, indicating that PENDANT 1 may be programmed. Within 5 seconds of connecting the battery press the ‘CANCEL’ button on the Medi-Alarm to enter program mode. The speaker will beep and the display will show ‘2’ on the display. • 6.3 PROGRAMMING OPTIONS Option Description TRANSMITTER 1 PROGRAM 1) 1 is on the display 2) Press the ‘HELP’ button to view programmed option.
Unprogrammed no device has been programmed for transmitter 1 a device is programmed for transmitter 1 programmed pendant remove previously programmed device erase To program a new pendant. • To test the signal strength of a Pendant. 1) C is on the display 2) Press the ‘Help’ button for the Medi-Alarm to accept a signal (‘-’ is displayed) 3) Press the ‘SIDE LEVER’ to check signal strength of transmitter. • PRIMARY PHONE NUMBER default - The primary telephone number is the first number that the dialler calls when an event message needs to be sent. 1) ‘N’ is on the display 2) Press the ‘HELP’ button to view programmed phone number. The programmed phone number will be flashed on status display. • Note: See example of telephone number 1 for more details.
Press the ‘Cancel’ button to move to the next program option. CLIENT ACCOUNT NUMBER The client account number identifies to the central station which Medi-Alarm is sending the alarm message. (Default 0000) 1) ‘A’ is steady on the display. Intel Parallel Studio Crack For Gta on this page. • ENABLE OVER DUE TIMER: The Over Due Timer is the time period between ‘CANCEL’ button presses to restart the over due timer.
I Wish to thank Steve and Robbie, for the installation and service I received,when my new alarm system was installed. Pc4820 v1.3 • installation manual warning: this manual contains information on limitations regarding product use and function and information on the.
Game Maker 8 Keygen. The over due timer is for local indication purposes only. (no alarm report is sent) 0-255 hours. Default = 0, disabled. 1,2 or 3 digits may be programmed with a maximum of 255 hours.
If a number greater than 255 is programmed, Medi Alarm will sound a long beep and re display the original value. • TEST CALL TIME. This option controls to time between the automatic test calls the Medi-Alarm will make. 1,2 or 3 digits may be programmed with a maximum of 255 hours. If a number greater than 255 is programmed, Medi Alarm will sound a long beep and re display the original value. 0 - 255 hours, default = 24 hours. • RESTORES ENABLED.
This option selects whether restore reports are sent to the central station if the alarm restores or the ‘CANCEL’ button is pressed. Default = r 1) ‘r’ is on the display steady. 2) Press the ‘HELP’ button to view the programmed value (r = restore reports, - = no restores) 3) Press the ‘HELP’. • Radio PIR The radio PIR is based on the Ness Quantum Ten+ design. It uses a 9 volt lithium battery as its power source, with it’s 4 minute sleep time, the battery life should be slightly longer. The PIR uses the Heimann Pyro Electric sensor for reliable stability.