] When riding is stopped, the speed will continue to count 4 seconds for Bike 1 and count 2 seconds for Bike2 to confirm that no more wheel signals have been sent. 00 Km or Mile +/- 0. 1% ODO: Odometer 0. 9 Km or Miles +/- 0. Attach the bracket to the handlebar and fit the rubber pad between the handlebar and the band of the bracket.
Slide the main unit onto the bracket from front to rear till it clicks into position. To remove the main unit, press down on the lock lever of the bracket then pull the main unit forward and off. ] The T-TM accumulates total riding time from the beginning of computer use and can not be cleared by the RESET operation. It will automatically begin counting upon riding, and continue to count 4 seconds for Bike1 and 2 seconds for Bike2 to confirm that no more wheel sensing signals have been sent when riding is stopped.
But this computer revises back the over-counted 2 or 4 seconds automatically. *: 12HR AM/PM or 24HR Clock 0. 003% AV: Average Speed 0:00'00' 12:59'59' AM/PM or 23:59'59' 0. 0Mile/h +/- It can display the current time in 12HR AM/PM or 24HR clock. It displays '0. 0' when TM is less than 4 sec., and is updated by about one second when TM is over 4 seconds.
It displays an 'Err' symbol when either the TM is over 100 hours or the DS is over 1, 000km (or miles). Reset the unit in order to restart. All descriptions are similar as the Lubrication Reminder except the word of Maintenance instead of Lubrication and the symbol ' ' shall be replaced by the symbol ' '. Sensor with Transmitter: No Contact Magnet sensor with Wireless Transmitter.
The Australian Cycling Forums by Bicycles Network Australia is the best resource. Echowell Echo F2 Computer. And the echowell website doesn't have the manual. If the computer is. Owner’s Manual. Arabic Software For Windows 7 Ultimate. Stand your bicycle upright. With your tire inflated to its proper pressure, rotate your wheel so that the valve.
Suitable Fork Size: 12mm to 50mm& (0. Wireless Sensing Distance: 55cm (1. 8 feet) between the transmitter and the main unit. Cross-Talking Interference: Within 40 cm (15. 8'), no interference by 2 bicycles carrying similar cycle computers, even when ridden side by side. Wheel Circumference Setting: 1mm - 3999mm (1mm increment) Operation Temperature: 0°C ~ 50°C (32°F ~ 122°F) Storage Temperature: - 10°C ~ 60°C (14°F ~ 140°F) Main Unit Battery Power: 3V battery x 1 (CR2032), battery operating life is about 2 years.
(Based on an average of 1. 5 hours use per day) Transmitter Battery Power: 1. 5V battery x 1 (typical LR44). About 24, 000km/15, 000 miles riding distance or 2 years battery operating life. (The original factory-attached battery life may be shorter than this period due to shipping and storage time). Dimensions and Weight Main Unit: 44. 5g Transmitter: 20.
1g DS: Trip Distance 0. 99 Km or Miles +/- 0.
1% The DS function accumulates the distance data from the last RESET operation as long as the bike is being ridden. * The specifications and designs may be changed without notice.
I NDEX: MEANS PRESS BUTTON N MORE THAN 2 SECONDS. } p LUBRICATION or MAINTENANCE REMINDER SETTING (For W2 only) p BIKE 1 or BIKE 2 SELECTION (For W2 only) (Fig. The patent-pending transmitter circuit is designed to reduce power consumption; a 1.
5V battery (typically an LR44) can operate for over 24, 000km (15, 000miles) riding distance or 2 years. Replace a new battery when the transmitter's battery power is nearly exhausted, otherwise the transmission power of the wheel signal will be weak, causing the main unit to display unstable data. Replace with a new LR44 battery 16 with the positive (+) pole toward the sensor cap 10.
Hold down the MODE button and SET button simultaneously for more than 3 seconds to initiate the computer and clear all data. IMPORTANT: Be sure to initiate the computer before it is be used, otherwise the computer may run errors.
The LCD segments will be tested automatically after the unit is initiated. The user's friendly function is to remind you about lubricating or maintaining your beloved bike after presetting the desired reminding distance. ] N): Get a suitable circumference value from the table. AUTOMATIC START/STOP & POWER AUTO ON/OFF The computer will automatically begin counting data upon riding and stop counting data when riding is stopped.